bat365官方网站登录

欢迎进入bat365官方网站登录|Enter-on line官网!
当前位置:首页 - 新闻中心 - 行业资讯

行业资讯

瓦斯bat365官方网站登录组被雨淋之后需注重保养方法

返回 2022.06.25 来源: 0
bat365官方网站登录组被雨淋之后需注重保养方法,这是很关键的一个事情,如不及时修护,将会造成bat365官方网站登录组锈蚀、腐蚀,出现损坏。下面来简单了解一番吧。
Maintenance methods should be paid attention to after the generator set is rained, which is a key thing. If it is not repaired in time, the generator set will be rusted, corroded and damaged. Let's have a brief look.
用水冲洗bat365官方网站登录外部,去除泥土和杂物,然后用金属清洁剂或洗衣粉去除表面的油渍。
Wash the outside of the generator with water to remove dirt and sundries, and then use metal cleaner or washing powder to remove oil stains on the surface.
支撑bat365官方网站登录一端,使油底壳放油部分处于低位,拧下放油螺塞,拉出油尺,让油底壳内的水自行流出。稍微让油和水一起排出,然后拧上放油塞。
Support one end of the generator so that the oil drain part of the oil pan is in the low position, screw the oil drain plug, pull out the dipstick, and let the water in the oil pan flow out by itself. Allow the oil and water to drain slightly, then screw on the oil drain plug.
拆下bat365官方网站登录组空气滤清器,拆下滤清器上壳,取出滤芯等部件,除去滤清器内的水分,用金属清洗剂或柴油清洗零件。如果过滤器是塑料泡沫制成的,应先用洗衣粉或肥皂水(无汽油)清洗,然后用清水冲洗干净,晾干,然后用适量机油浸泡(浸泡后用尽量用手)。更换新滤清器时应进行同样的油浸处理。滤芯是纸质的,需要更换新的。过滤器各部件清洗干燥后,按规定安装。
Remove the air filter of the generator set, remove the upper shell of the filter, take out the filter element and other components, remove the water in the filter, and clean the parts with metal cleaner or diesel oil. If the filter is made of plastic foam, it should be cleaned with washing powder or soapy water (without gasoline), then washed with clean water, dried, and soaked with an appropriate amount of engine oil (after soaking, use your hands as much as possible). Replace the new filter with the same oil immersion treatment. The filter element is paper and needs to be replaced. After the filter components are cleaned and dried, they shall be installed as required.
拆下进、排气管和消音器,排除内部积水。开启减压,摇动bat365官方网站登录,看进、排气口是否有水排出。如果有水排出,继续摇动曲轴,直到气缸内的水全部排出。安装进排气管和消音器,在进气口加少许油,曲轴转动几次,然后安装空气滤清器。如果由于bat365官方网站登录进水时间长而使飞轮转动困难,则说明缸套和活塞环已经生锈。应将它们拆下以去除锈迹,清洁后再组装。如果锈蚀严重,应及时更换。
Remove the intake and exhaust pipes and silencer to drain the internal water. Turn on the pressure reducer, shake the generator, and check whether there is water discharged from the inlet and outlet. If water is drained, continue to shake the crankshaft until all the water in the cylinder is drained. Install the air inlet and exhaust pipe and silencer, add a little oil to the air inlet, turn the crankshaft several times, and then install the air filter. If it is difficult for the flywheel to rotate due to the long water inflow time of the generator, it indicates that the cylinder liner and piston ring have been rusted. They should be removed to remove rust and cleaned before assembly. If the corrosion is serious, replace it in time.
瓦斯bat365官方网站登录组
拆下油箱,将油箱内的油水全部排出。检查滤清器和油管内是否有水,如果有水,应将其放掉。清洁油箱和柴油滤清器,然后将它们放回原位,连接燃油回路,将清洁的柴油加入油箱。
Remove the oil tank and drain all the oil and water in the tank. Check whether there is water in the diesel filter and oil pipe. If there is water, drain it. Clean the fuel tank and diesel filter, then put them back in place, connect the fuel circuit, and add clean diesel to the fuel tank.
放掉水箱和水路中的污水,清洗水路,加入干净的河水或煮沸的井水,直到水浮起。打开油门开关并启动bat365官方网站登录。瓦斯bat365官方网站登录组启动后,注意观察油位指示器的上升情况,听bat365官方网站登录是否有异响。检查所有部件是否正常后,在bat365官方网站登录中运行。磨合顺序为先怠速、后中速、后高速,每次运行时间为5min。磨合后,停机放油。重新添加新油,启动bat365官方网站登录,中速运转5分钟,即可正常使用。
Drain the sewage from the water tank and waterway, clean the waterway, and add clean river water or boiled well water until the water floats. Open the throttle switch and start the generator. After the generator of the gas generator set is started, pay attention to the rise of the oil level indicator and listen to whether the generator has abnormal noise. After checking whether all components are normal, operate in the generator. The running in sequence is idling first, then medium speed, and then high speed, and each running time is 5min. After running in, stop the machine and drain the oil. Add new oil again, start the generator and run it at medium speed for 5 minutes, and then it can be used normally.
采取以上措施,可有效使bat365官方网站登录组恢复到良好状态,消除后期运行的安全隐患。当然要提醒大家,如果bat365官方网站登录组必须在室外使用,请随时封锁工作,以防突发天气造成不必要的损失。
Taking the above measures can effectively restore the generator set to a good state and eliminate the potential safety hazards in later operation. Of course, we should remind you that if the generator set must be used outdoors, please block the work at any time to prevent unnecessary losses caused by sudden weather.
以上就是问题解答的相关内容了,希望能够帮助到大家,如对这一问题还存在任何疑问,都欢迎关注我们网站并咨询我们的工作人员,将竭诚为您服务。
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website And consult our staff, will serve you wholeheartedly.
新闻搜索
bat365官方网站登录|Enter-on line
  • 服务热线

    0531-62325028
    0531-69951266

瓦斯bat365官方网站登录组被雨淋之后需注重保养方法

bat365官方网站登录组被雨淋之后需注重保养方法,这是很关键的一个事情,如不及时修护,将会造成bat365官方网站登录组锈蚀、腐蚀,出现损坏。下面来简单了解一番吧。
Maintenance methods should be paid attention to after the generator set is rained, which is a key thing. If it is not repaired in time, the generator set will be rusted, corroded and damaged. Let's have a brief look.
用水冲洗bat365官方网站登录外部,去除泥土和杂物,然后用金属清洁剂或洗衣粉去除表面的油渍。
Wash the outside of the generator with water to remove dirt and sundries, and then use metal cleaner or washing powder to remove oil stains on the surface.
支撑bat365官方网站登录一端,使油底壳放油部分处于低位,拧下放油螺塞,拉出油尺,让油底壳内的水自行流出。稍微让油和水一起排出,然后拧上放油塞。
Support one end of the generator so that the oil drain part of the oil pan is in the low position, screw the oil drain plug, pull out the dipstick, and let the water in the oil pan flow out by itself. Allow the oil and water to drain slightly, then screw on the oil drain plug.
拆下bat365官方网站登录组空气滤清器,拆下滤清器上壳,取出滤芯等部件,除去滤清器内的水分,用金属清洗剂或柴油清洗零件。如果过滤器是塑料泡沫制成的,应先用洗衣粉或肥皂水(无汽油)清洗,然后用清水冲洗干净,晾干,然后用适量机油浸泡(浸泡后用尽量用手)。更换新滤清器时应进行同样的油浸处理。滤芯是纸质的,需要更换新的。过滤器各部件清洗干燥后,按规定安装。
Remove the air filter of the generator set, remove the upper shell of the filter, take out the filter element and other components, remove the water in the filter, and clean the parts with metal cleaner or diesel oil. If the filter is made of plastic foam, it should be cleaned with washing powder or soapy water (without gasoline), then washed with clean water, dried, and soaked with an appropriate amount of engine oil (after soaking, use your hands as much as possible). Replace the new filter with the same oil immersion treatment. The filter element is paper and needs to be replaced. After the filter components are cleaned and dried, they shall be installed as required.
拆下进、排气管和消音器,排除内部积水。开启减压,摇动bat365官方网站登录,看进、排气口是否有水排出。如果有水排出,继续摇动曲轴,直到气缸内的水全部排出。安装进排气管和消音器,在进气口加少许油,曲轴转动几次,然后安装空气滤清器。如果由于bat365官方网站登录进水时间长而使飞轮转动困难,则说明缸套和活塞环已经生锈。应将它们拆下以去除锈迹,清洁后再组装。如果锈蚀严重,应及时更换。
Remove the intake and exhaust pipes and silencer to drain the internal water. Turn on the pressure reducer, shake the generator, and check whether there is water discharged from the inlet and outlet. If water is drained, continue to shake the crankshaft until all the water in the cylinder is drained. Install the air inlet and exhaust pipe and silencer, add a little oil to the air inlet, turn the crankshaft several times, and then install the air filter. If it is difficult for the flywheel to rotate due to the long water inflow time of the generator, it indicates that the cylinder liner and piston ring have been rusted. They should be removed to remove rust and cleaned before assembly. If the corrosion is serious, replace it in time.
瓦斯bat365官方网站登录组
拆下油箱,将油箱内的油水全部排出。检查滤清器和油管内是否有水,如果有水,应将其放掉。清洁油箱和柴油滤清器,然后将它们放回原位,连接燃油回路,将清洁的柴油加入油箱。
Remove the oil tank and drain all the oil and water in the tank. Check whether there is water in the diesel filter and oil pipe. If there is water, drain it. Clean the fuel tank and diesel filter, then put them back in place, connect the fuel circuit, and add clean diesel to the fuel tank.
放掉水箱和水路中的污水,清洗水路,加入干净的河水或煮沸的井水,直到水浮起。打开油门开关并启动bat365官方网站登录。瓦斯bat365官方网站登录组启动后,注意观察油位指示器的上升情况,听bat365官方网站登录是否有异响。检查所有部件是否正常后,在bat365官方网站登录中运行。磨合顺序为先怠速、后中速、后高速,每次运行时间为5min。磨合后,停机放油。重新添加新油,启动bat365官方网站登录,中速运转5分钟,即可正常使用。
Drain the sewage from the water tank and waterway, clean the waterway, and add clean river water or boiled well water until the water floats. Open the throttle switch and start the generator. After the generator of the gas generator set is started, pay attention to the rise of the oil level indicator and listen to whether the generator has abnormal noise. After checking whether all components are normal, operate in the generator. The running in sequence is idling first, then medium speed, and then high speed, and each running time is 5min. After running in, stop the machine and drain the oil. Add new oil again, start the generator and run it at medium speed for 5 minutes, and then it can be used normally.
采取以上措施,可有效使bat365官方网站登录组恢复到良好状态,消除后期运行的安全隐患。当然要提醒大家,如果bat365官方网站登录组必须在室外使用,请随时封锁工作,以防突发天气造成不必要的损失。
Taking the above measures can effectively restore the generator set to a good state and eliminate the potential safety hazards in later operation. Of course, we should remind you that if the generator set must be used outdoors, please block the work at any time to prevent unnecessary losses caused by sudden weather.
以上就是问题解答的相关内容了,希望能够帮助到大家,如对这一问题还存在任何疑问,都欢迎关注我们网站并咨询我们的工作人员,将竭诚为您服务。
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website And consult our staff, will serve you wholeheartedly.